29
Nov 17

Another interloper

No work in the shed last night, on account of aches, pains, freezing despite sitting beside the fire, and the usual pre-cold fun stuff. I crashed, went to bed, worked from home today (yes, you can type while under a duvet), and by afternoon was feeling somewhat more human.

So this evening when junior and mommy got back home, junior and I opened the large boxes from FFX and Rutlands that arrived over the last day or two and dragged the latest interloper to the shed…

It’s… slightly larger than anticipated. But not by too much. What it was wasΒ loud. The specs said under 85dbA, the meter says 96dbA. And when you start sanding, it peaks somewhere around 106dbA – 3dBA louder than the dang bandsaw. Hmmm. Maybe when it’s on the base and everything’s nailed down… yeah, who am I kidding. Not sure what to do about this. At least it doesn’t have a lot to do in the shed, it’s mainly for bandsaw boxes and the like.

Well, at least I’m all stocked up on glue for a while. I’m looking forward to trying the plastic razor blades as well to see how they cope with glue cleanup. The angle box may be useful for the bandsaw and the sanding table, all the dremel sanding paper should be useful for small parts, and the black-and-white tube there on the right up against the triton are some teflon rods that I’m going to use to replace the steel rods that are the bandsaw guides on the bandsaw. This way I figure I can tighten the guides up against the blade itself, turn it on for a minute or so and it’ll wear away the teflon to get the perfect spacing without damaging the blade. We’ll see. There are some smaller ball bearings in the post as well to try to replace the thrust bearings with so the larger blades don’t contact them when running without load, which is how every guide out there says to set them up (the bandsaw guide holder I have just won’t let me adjust that, because Cheap Tool πŸ˜€ ).

Also got a few grades of sandpaper for the sander. Now I have to figure out where to put all this stuff. I had a plan to put together a very, very rough platform from some 2x4s that were left over from making the bench…

The key here is to do this fast. Other projects are a-waiting, but until this is done I literally can’t get my bench back, there’s nowhere to put the Triton. So it’s all butt joints and glue and screws and forget face planing or anything we don’t have to do…

That’s the twp sides done. Next up, five crossbars (two up top, two undeneath which get castors later, and one at the back for cross-bracing), all of which will be lap-jointed to the sides along with glue and screws. And if I can find metal bracing brackets tomorrow I’ll use those too. This thing is going to be ugly and I don’t care, I’ll do a nicer one later on. Like, after this one breaks.

BTW, on the right, a Bosch power drill. On the left (well, in the middle really), a brace with a hex key screwdriver bit that doesn’t really fit the jaws. Three guesses which one crapped out on me after the second screw?

Hint: it wasn’t the seventy-year-old tool that has so much torque it could twist the screw into a pretzel if you wanted to.

Stupid batteries. If I wanted to replace them, I’d just buy a new drill – it’s almost cheaper that way (do you want one battery for 50 euro or two batteries and a new drill for 80?). Gah.


24
Nov 17

Ending, restocking, brexit and black friday

Looooong day. I had a callout over the weekend at midnight on Saturday so I had a few hours off in lieu that I took this morning to go to the timber yard. One of the next projects coming up could use some 8/4 oak so my shopping list was a 6-8″ board of 8/4 oak between 8′ and 12′, an 8-9″ board of 4/4 oak around the 12′ mark, and possibly the same two boards again in walnut. And I thought I’d take a look at the beech and get a small board of that to try working in it.

You know how plans rarely survive contact with reality?

So, Brexit. And now any timberyard here in Ireland has a choice – either get hardwoods direct from the continent via ship which is more expensive than road haulage; or buy it from the continent and drive it back home through the UK with all the customs hassle on both coasts which is expensive; or do what they’ve done till now and buy smaller quantities from UK timberyards and ship it back on the ferry to here, but now paying higher prices because the pound has collapsed, and next year, paying higher prices again because the UK is having to pay customs duties of 20% or more on their imports from the EU (because the UK does not grow enough timber for itself and hasn’t since the 18th century), and then paying higher prices again because of customs duties re-importing that timber back here.

The shorter version of that is, Because Brexit, hardwood now costs 150% or so of what it cost this time last year. Except maybe for that german beech, which I think was roughly the same.

(Oh, and forget about looking to the US, they’ve finished one round of 20% tarrifs on canadian softwood and the entire softwood and hardwood market rising to match that, and they’re now looking at another 20% round Real Soon Now).

So, 8/4 oak board? No worries, Paul had an 8′ board from the end of a pack. Grand for me, no knots, no damage, slight cup but the parts I’ll be making are 1′ or shorter so that’s no worry. But it’s €60/cb.ft. The 4/4 oak is around €45/cb.ft, up from €30. The 4/4 walnut is closing on €90/cb.ftΒ and the 8/4 walnut… well, the one board I’d picked out (8/4 6″x10′) was €140. Alas, it remains in the warehouse πŸ˜€

The beech on the other hand, was beautiful stuff, I had the first pick from a freshly opened pack and it had lovely clear grain, so I wound up buying two cubic feet in four boards, way more than I intended to but it was just so damn nice looking and so cheap compared to the rest (at around €24/cb.ft) that I thought it would have been a mistake to leave it behind.

A few minutes with the circular saw to break it down enough to fit in both my car and the shed, and then it was time to test the new car’s timber carrying capacity (the old car gave up the ghost earlier this year and we had to change).

Huzzah! It took all of three minutes to pull those seats last night (they’re built to lift right out, it’s quite neat and tidy) and once loaded I could close the boot and drive home without any fuss. Score one for the Yeti.

Once I got it home, I had to clean up the shed slightly – the floor had about 3″ of shavings and crud built up on it because of the rush on the boxes, so that had to go and the timber store had to be quickly shuffled to make some room, and then it was the haul-it-through-the-house routine:

Nice piece of 8/4 oak there.

And there’s that lovely beech’s grain and the other half of the 8/4 oak board. But all of that has to go in here somehow:

There was considerable shuffling πŸ˜€ But…

Done! πŸ˜€ Just don’t ask me to get anything out of there in less than half an hour…

And cleaned down and ready for the next project (or more accurately to go back to the one I was in the middle of when I stopped to do the boxes).

Speaking of the boxes…

The oak was a disaster:

Just tore themselves apart along the glue lines after the ebonising (and the ebonising didn’t go well, I think some of the tannic acid got into the iron solution and nullified it, I’ll have to make some more). So those got ditched. But the rest were okay.

Dropped those off at the school in the afternoon for the bazaar and they hadn’t a clue what to do with them so they’re lumped in with the bric-a-brac. Oh well, might get them a bit more notice next year. This year though, someone’s getting handmade boxes rather cheaply πŸ˜€

It’ll be interesting to see if they actually do sell, if they do I might make a piece explicitly to sell next year, just to see if it would.

 

Oh, and today’s Black Friday, so I bought a sander πŸ˜€

(along with a few belts and spindles for medium and fine grades to go with the coarse set it comes with). I know it *looks* like a fancy version of a belt sander turned on its side, but it’s a bit better than that. For a start, better dust collection and about 26dBA quieter πŸ˜€ Plus, you can swap out the belt for a spindle to do curved surfaces:

And of course, it has built-in storage all over the place which is nice (but doubtless not enough if you have more than one grade of sandpaper). So I’ll build a plywood platform for it and a 2×4 framework to let me store it below the bandsaw. Getting cramped in the shed now though…

And Rutlands were also doing a sale so I got some more titebond (I’m down to my last bottle), a spare silicone glue brush set (because I’m always waiting for the two brushes I have to finish drying before I can use them again), and some other small doodads and gimmicks like plastic razor blades. But hey, if amateurs don’t buy this stuff, who will? πŸ˜€


Stochastic Geometry is Stephen Fry proof thanks to caching by WP Super Cache